Tools Fork

S-TECH TOOL FOR ADJUSTING THE COMPRESSION

-NO NEED TO REMOVE THE HANDLEBAR
-WITH GUIDE

Fits all KYB CC forks.

S-TECH TOOL FOR REMOVING THE FORK CAP FROM THE PISTON ROD.

- FOR WP XPLOR FORKS WITH EXTERNAL SPRING PRELOAD

S-TECH TOOL FOR ADJUSTING THE COMPRESSION

- NO NEED TO REMOVE THE HANDLEBAR.
- THE SMALL 25MM DIAMETER ALLOWS FOR USE EVEN ON HARD-TO-REACH ADJUSTERS.

Universal adapter with three wrench sizes for suspension workshops. The 22mm side has a hole and is therefore suitable, for example, as an adapter insert for opening the SHOWA SFF-AIR fork on the CRF 250 (screw connection with valve).
Wrench sizes:
19 mm
22 mm
24 mm

Tool for changing fork springs (WP35).

KTM SX50 (2012 and later)

KTM SX65 (2012 and later)

Adapter insert for opening the compression unit of the SACHS fork (closed cartridge)

SW: 38/24

Adapter insert for opening the compression damping unit of the WP Closed Cartridge fork
or the damping side of the WP AER fork.

Adapter insert for opening the compression unit of the WP Conve Valve / Pro Components fork

- Wrench size: 17 / 19 mm hex
- WITH HOLLOW BORE - ALLOWS DISASSEMBLY EVEN WITH THE PISTON ROD INSTALLED
- SUITABLE FOR ALL CARTRIDGE HEADS WITH 17MM OR 19MM INTERNAL HEX

Adapter insert for opening the compression stage unit of the:

SHOWA SFF-AIR fork
all SHOWA closed-cartridge forks
all KYB closed-cartridge forks

as well as

the spring-side cap of the SHOWA SFF fork.

Dimensions: 36 / 19

• For positioning the Delta shims on the WP rebound piston
• Suitable for Ø20 Delta shims and 23mm pistons
• Quick and easy to use
• Shims can no longer twist

Removal lever for removing O-rings from fork tubes

Tool set for removing O-rings and other seals

-Clean surface

-No sanding block required

-Work faster and more efficiently

-Clean surface

-No sanding block required

-Work faster and more efficiently

The K-Tech Off-Road Fork Work Station was designed for precision, organization, and efficiency, and is the ultimate service companion for suspension specialists and dedicated motorcycle enthusiasts. Designed to securely hold multiple fork components during disassembly and maintenance, this purpose-built work station keeps your workspace organized while allowing oil to drain safely from critical suspension parts.

The workstation was specifically designed for off-road forks to support inner and outer fork tubes, cartridges, shock rods, and shock assemblies during maintenance. Each component can be securely placed in its designated holders while excess fork oil drains away, preventing mess and improving workflow efficiency. Since all parts are stored upright and organized in a single compact station, technicians gain more usable workspace and better visibility, which helps streamline complex suspension maintenance tasks.

• Key Benefits

  • Secure Storage of Components—Safely stores fork tubes, cartridges, piston rods, and damping assemblies during maintenance.
  • Better Organization in the Workshop—Keeps suspension parts organized and easily accessible.
  • Oil Drain Management—Allows fork components to drain naturally while being held in place.
  • Space-saving design—Saves valuable bench space during suspension overhauls.
  • Precision tool for the workshop—Ideal for suspension technicians, racing teams, and ambitious mechanics.

YAMAHA TENERE FORK CLAMP TOOL CARTRIDGE

For holding/securing fork tubes

Material: Stainless steel, PVC-coated

• For holding the adjustment tabs during disassembly and assembly
• Suitable for forks and shock absorbers
• Oversized design, so it also works with standard aftermarket adjusters

K-TECH TOOL FOR OPENING ÖHLINS FORKS

Bolt circle diameter: 39 mm
Pin diameter: 3.50 mm

S-TECH TOOL FOR RELIEVING PRESSURE ON FORK SPRINGS

- MAKES IT EASIER/SIMPLER TO REMOVE THE FORK SPRING ON ROAD BIKES!

REPLACEMENT CANNULA SUITABLE FOR OUR NEEDLE FILLING DEVICES WITH THE FOLLOWING PART NUMBER:
213-900-010
70240
70242

1 set (10 pieces)

Tool for removing and holding the fork piston rod

-> for bleeding the fork
-> for removing the piston rod to install the threaded fitting
-> 4 thread sizes integrated, allowing it to accommodate the most common piston rods.
-> Extra-long version (L=300 mm)

4 thread sizes:
- M12 x 1.25
- M12 x 1.0
- M10 x 1.25
- M10 x 1.0

Tool for removing and holding the fork piston rod

-> for bleeding the fork
-> for removing the piston rod to install the screw connection

Thread sizes:
M13 x 1.0

Plate for securing the fork piston rod
allows the piston rod screw connection to be loosened
Combination holder (fits Ø10, Ø12, Ø12.5, Ø14)
Aluminum T6061 - CNC-machined, anodized